Westgate DV62 Spezifikationen

50-2163SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.TECHNICALMANUALDV62This appliance may b

Figure 10. Typical Framing for Corner - Detailed.Planning your inStallationtypicaL FRaming - coRneR:Figure 9. Typical Framing for Corner - General.1

11Figure 11. Typical Framing for Sidewalls & Mantel - General.Figure 12. Typical Framing for Sidewalls & Mantel - Detailed.Planning your inS

Figure 14. Typical Framing for a Raised Hearth - Detailed.Planning your inStallationtypicaL FRaming - RaiseD heaRth:Warning: Failure to follow these

13Planning your inStallationFigure 15. Facing Trim Installation - General.instaLLation oF Facing tRim:

14Figure 16. Typical Facing for the Fireplace - General.Planning your inStallationThe DV62 may be installed with an optional front. The front

Planning your inStallationFigure 19. Option 3 - Fireplace Facing Less than 1” (25.4mm) Thick With Optional Fronts Installed.instaLLation oF FiRepLace

Planning your inStallationinstaLLation oF ReceiveR:Figure 20. Receiver Installation.The Receiver is the heart of the remote control system. You need

17Planning your inStallationFigure 21. Allowable Vent Congurations Chart.

Figure 22. Vent Termination Restrictions, refer to Table 1.AADELBCFBBBJMKGHIOpenableFixedClosedOpenableFixedClosedTermination CapAir Supply InletGas

19Planning your inStallationappRoveD vent paRts:Table 2: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).Part Description S

FOR SAFE INSTALLATION AND OPERATION OF YOUR “WESTGATE” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All Westgate gas-red applian

instaLLation oF FLue RestRictoR:Flue Restrictor is necessary to keep the replace running at its intended efciency. They are also req

21inStallation Set-uPQUALIFIED INSTALLERS ONLYpLanning youR instaLLation:Prior to starting your venting installation, refer to the section on Allowabl

instaLLation oF non-combustibLe waLL boaRD:Install the non-combustible wall board provided with the unit. The side boards are interchangeable and are

instaLLation oF venting anD teRminations:Read all instructions carefully before starting the installation. Failure to follow these instructions may cr

Notes:(1) Any horizontal run of vent must have a ¼ inch (6mm) rise for every 1 foot (305mm) of run towards the termination. Never allow the v

25inStallation Set-uPFigure 33: Installation of Wall Firestop.Figure 34: Typical Minimum Vent Congurations - Horizontally Terminated.Step 6. Before

veRticaL teRmination instaLLation:Step 1. M a i n t a i n c l e a r a n c e s between venting and combustible building materials as stated ear

Notes:(1) If an offset is necessary in the attic to avoid obstructions, it is important to support the vent pipe every 3 feet, to avoid excessive st

inStallation Set-uPHDimension ‘H’ obtainedfrom table to the left.Table 3: Minimum ‘H’ for Figure 40.Roof Pitch Minimum Height (H)Feet MetersFlat to 7/

29inStallation Set-uP4) Lift the Door Frame away, being careful that the glass panel is secure within the Door Frame.Figure 44: Door Latch Locat

table of contentSSafety Precautions...2Table of Contents...

inStallation Set-uPeLectRicaL hook-up:An electrical junction box is provided and fastened to the back of the control box. Power needs to be

31inStallation Set-uPFigure 52: Rigjt Firebox Liner Panel in Place.Figure 49: Left Firebox Liner Panel in Place Figure 50: Top Firebox Liner Panel Ins

inStallation Set-uPLog buRneR / embeR beD instaLLation:1. In the bottom rear of the rebox there are two (2) gas orices in a housing that

33inStallation Set-uPFigure 59: Tab on Firebox Grate.Figure 58: Slot for Firebox Grate.Figure 60: Firebox Grate in Place.Figure 57: Burner Accents Pie

Figure 61b: Log 8 in PlaceFigure 62b: Log 7 Front End1. Install Log 8. Insert the pin hole on the front end of log 8 into the pin tab locates at the

35inStallation Set-uPFigure 64b: Log 5 in PlaceFigure 65: Log 6 in Place3. Install Log 9. Insert the hole on the left side into the pin tab at the b

inStallation Set-uP366. Install Log 10. Place the end with number 10 against the notch on log 8 and rest the other end on the groove of log 7. The

Figure 69b: Log 9 in Place.inStallation Set-uPFigure 68b: Log 1 in Place.Figure 70b: Log 3 in Place8. Install Log 1. Position log 1 to sit on the ri

inStallation Set-uP38NOTE: Variances in gas quality or log placement may cause some discoloration of the log set, or sooting to occur.

Figure 72: Mixing Tubes in Glass Burner.Figure 73: Placing Glass Burner.1. In the bottom rear of the rebox there are two (2) gas orices

DIRECT VENT ONLY: This type is identied by the prex DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec

6. Gently place the burner trim piece around the burner (see Figure 77). It sits on various support brackets and ts around the burner tr

411. Install the Rear Firebox Liner. This panel rests on the Rear Brick Panel Support. 2. Install the Left Firebox Liner Panel; it sits on t

Figure 85: Installing Burner Cover Support KitFigure 86: Permanent Magnet on Right Burner Cover Support.inStallation Set-uPFigure 87: Slots in Back of

43inStallation Set-uP14. Install the Burner Assembly; refer to Step 1 & 2 of log Burner / emBer Bed insTallaTion.15. Install the Left and Righ

inStallation Set-uPFigure 93: Optional Front Installed.Install the front by lifting it parallel to the replace with the mounting bracket

45Wiring HarneSSCaution: Label all wires prior to disconnection when servicing controls, Wiring errors can cause improper and dangerous operation. Ver

diagnoStic flaSH codeS1. Fail to ignite: If there is no positive ignition, the board will go into lock out and the LED will blink 3 times in intervals

47troubleSHootingProblem Possible Cause SolutionThermostat does not workThe pilot ame has gone out· Turn it ONThe On/Off switch is turn to OFFThe the

troubleSHootingProblem Possible Cause SolutionLocking conditionsReset the Proame DFC board· Turn the system off by pressing the ON/OFF button on the

49PartS diagram

5Rating LabeL Location:SPecificationSDimensions:Figure 1. Dimensions of the Firebox.The Rating and Lighting instruction label is located below the do

PartS diagram - oPtionS50

51PartS liStItem Number Items1 50-1980Crushed Glas - White2 50-1984Crushed Glas - Black3 50-2234Log Set4 50-2233Log Grate5 50-2235Log Burner Accent -

WarrantySherwood Industries Ltd. is the manufacturer of the Westgate line of heating products. At Sherwood Industries, our commitment

5312. The Limited Warranty is void if: a) The stove has been operated in atmospheres contaminated by chlorine, uorine or other damaging chemicals.

inStallation data SHeetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:__________

SPecificationSRating LabeL:Figure 3. Rating Label.SAMPLE6

7Planning your inStallationintRoDuction:This section of the technical manual is for the use of qualied technicians only. Fireplace pla

Figure 6. Typical Framing for Internal Chase - Detailed.Planning your inStallationtypicaL FRaming - inteRnaL chase:Figure 5. Typical Framing for Int

9Figure 7. Typical Framing for External Chase - General.Figure 8. Typical Framing for External Chase - Detailed.Planning your inStallationtypicaL FR